3D Print Downloads   v1.0

Released  —  License

If you have a 3D Printer, you can build your own Marty!

You'll also need some electronics components to complete your Marty, we'd recommend our Control Board, Rick, 4 K-Power DMM016 Servos and 5 HobbyKing HK15178 Servos, a battery plus Charger, and optionally a Raspberry Pi and Camera.

Timings, layer heights and infill percentages are our recommendations based on printing with a BCN3D Sigma, Ultimaker 2 and Prusa i3.

The parts from our previous v0.1 release are still available, you'll find a link to them at the bottom of this page.

Recommended Additional Components:

Marty the Reindeer - Nose

Marty the Reindeer - Nose

Quantity Required: 1
Approx. print time: 58min
Approx. filament weight: 7g
Layer height: 0.15mm
Infill: 50%

Marty the Reindeer - Antlers

Marty the Reindeer - Antlers

Quantity Required: 2
Approx. print time: 1hr22min
Approx. filament weight: 11g
Layer height: 0.15mm
Infill: 50%

Foot (Robotical Type)

Foot (Robotical Type)

Quantity Required: 2
Approx. print time: 2hr11min
Approx. filament weight: 18g
Layer height: 0.15mm
Infill: 33%

RaspberryPi Camera Mount Bracket

RaspberryPi Camera Mount Bracket

Quantity Required: 1
Approx. print time: ???
Approx. filament weight: ???
Layer height: 0.15mm
Infill: ???

RaspberryPi Camera Mount

RaspberryPi Camera Mount

Quantity Required: 1
Approx. print time: ???
Approx. filament weight: ???
Layer height: 0.15mm
Infill: ???

Side Panel

Side Panel

Quantity Required: 2
Approx. print time: ???
Approx. filament weight: ???
Layer height: 0.15mm
Infill: ???

Hand

Hand

Quantity Required: 2
Approx. print time: 19min
Approx. filament weight: 3g
Layer height: 0.15mm
Infill: 33%

Arm

Arm

Quantity Required: 2
Approx. print time: 39min
Approx. filament weight: 6g
Layer height: 0.15mm
Infill: 33%

Arm Gear

Arm Gear

Quantity Required: 2
Approx. print time: 22min
Approx. filament weight: 4g
Layer height: 0.15mm
Infill: 33%

Arm Servo Gear

Arm Servo Gear

Quantity Required: 2
Approx. print time: 26min
Approx. filament weight: 4g
Layer height: 0.15mm
Infill: 33%

Servo Link (Default Type)

Servo Link (Default Type)

Quantity Required: 4
Approx. print time: 18min
Approx. filament weight: 2g
Layer height: 0.15mm
Infill: 33%

Servo Link (Robotical Type)

Servo Link (Robotical Type)

Quantity Required: 4
Approx. print time: 18min
Approx. filament weight: 2g
Layer height: 0.15mm
Infill: 33%

Link

Link

Quantity Required: 12
Approx. print time: 17min
Approx. filament weight: 2g
Layer height: 0.15mm
Infill: 33%

Cross Brace

Cross Brace

Quantity Required: 8
Approx. print time: 17min
Approx. filament weight: 3g
Layer height: 0.15mm
Infill: None

Thrust Washers

Thrust Washers

Quantity Required: 2
Approx. print time: 3min
Approx. filament weight: 1g
Layer height: 1.0mm
Infill: None

Twist Shaft

Twist Shaft

Quantity Required: 2
Approx. print time: 26min
Approx. filament weight: 2g
Layer height: 1.0mm
Infill: None

Servo Mount (1 Pin)

Servo Mount (1 Pin)

Quantity Required: 4
Approx. print time: 46min
Approx. filament weight: 6g
Layer height: 0.15mm
Infill: 33%

Servo Holder (2 Pin)

Servo Holder (2 Pin)

Quantity Required: 8
Approx. print time: 47min
Approx. filament weight: 6g
Layer height: 0.15mm
Infill: 33%

Foot (Old Type)

Foot (Old Type)

Quantity Required: 2
Approx. print time: 2hr11min
Approx. filament weight: 18g
Layer height: 0.15mm
Infill: 33%

Eye Cup Washer

Eye Cup Washer

Quantity Required: 1
Approx. print time: ???
Approx. filament weight: ???
Layer height: ???
Infill: 0%

Left Eye

Left Eye

Quantity Required: 1
Approx. print time: 56min
Approx. filament weight: 6g
Layer height: 1.0mm
Infill: 33%

Right Eye

Right Eye

Quantity Required: 1
Approx. print time: 58m
Approx. filament weight: 6g
Layer height: 1.0mm
Infill: 33%

Head Base

Head Base

Quantity Required: 1
Approx. print time: 4hr30m
Approx. filament weight: 51g
Layer height: 0.2mm
Infill: None

Head Face

Head Face

Quantity Required: 1
Approx. print time: 5hr
Approx. filament weight: 58g
Layer height: 0.2mm
Infill: None

LICENSE


All Releases: